当前位置：首 页 --> 方案设计
MCP8025三相BLDC马达驱动方案
发布时间：2016/3/7 13:32:00 来源：
Microchip公司的MCP8025/6是三相无刷DC(BLDC)马达栅极驱动器,包括有三个能驱动三个外接NMOS/NMOS晶体管对的半桥驱动器,在12V时可提供0.5A的峰值输出电流.器件集成了比较器,降压稳压器,两个LDO稳压器,电源监测比较器,超温传感器,LIN收发器,零交叉检测器,中性模拟器和运算放大器.主要用在汽车燃料泵,水泵和通风马达,家用电器,PMSM控制,业余爱好飞机,船和卡车.本文介绍了MCP8025/6主要特性,框图和典型应用电路,以及MCP8025 TQFP BLDC马达驱动评估板主要特性,框图,电路图,材料清单和PCB设计图.
The MCP8025/6 devices are 3-phase brushless DC(BLDC) power modules containing three integratedhalf-bridge drivers capable of driving three externalNMOS/NMOS transistor pairs. The three half-bridgedrivers are capable of delivering a peak output currentof 0.5A at 12V for driving high-side and low-side NMOSMOSFET transistors. The drivers have shoot-through,overcurrent and short-circuit protection. A Sleep Modehas been added to achieve a typical “key-off” quiescentcurrent of 5 μA.
The MCP8025 device integrates a comparator, a buckvoltage regulator, two LDO regulators, powermonitoring comparators, an overtemperature sensor, aLIN transceiver, a zero-crossing detector, a neutralsimulator and an operational amplifier for motor current monitoring. The phase comparator and multiplexerallow for hardware commutation detection. The neutralsimulator allows commutation detection without aneutral tap in the motor. The buck converter is capableof delivering 750 mW of power for powering acompanion microcontroller. The buck regulator may bedisabled if not used. The on-board 5V and 12V lowdropoutvoltage regulators are capable of delivering30 mA of current.
The MCP8026 replaces the LIN transceiver, neutralsimulator and zero-crossing detector in MCP8025 withtwo level shifters and two additional op amps.
The MCP8025/6 operation is specified over atemperature range of -40℃ to +150℃.Package options include 40-lead 5x5 QFN and 48-lead7x7 TQFP with Exposed Pad (EP).
MCP8025主要特性:
• AEC-Q100 Grade 0 Qualified
• Quiescent Current:
- Sleep Mode: 5 μA Typical
- Standby Mode:<200 μA
• LIN Transceiver Interface (MCP8025):
- Compliant with LIN Bus Specifications 1.3,2.2, and SAE J2602
- Supports baud rates up to 20K baud
- Internal pull-up resistor and diode
- Protected against ground shorts
- Protected against loss of ground
- Automatic thermal shutdown
- LIN Bus dominant timeout
• Three Half-Bridge Drivers Configured to DriveExternal High-Side NMOS and Low-Side NMOSMOSFETs:
- Independent input control for high-sideNMOS and low-side NMOS MOSFETs
- Peak output current: 0.5A @ 12V
- Shoot-through protection
- Overcurrent and short circuit protection
• Adjustable Output Buck Regulator (750 mW)
• Fixed Output Linear Regulators:
- email protected
- email protected
• Operational Amplifiers:
- one in MCP8025
- three in MCP8026
• Overcurrent Comparator with DAC Reference
• Phase Comparator With Multiplexer (MCP8025)
• Neutral Simulator (MCP8025)
• Level Translators (MCP8026)
• Input Voltage Range: 6V – 40V
• Operational Voltage Range:
- 6V–19V (MCP8025)
- 6V–28V (MCP8026)
• Buck Regulator Undervoltage Lockout: 4.0V
• Undervoltage Lockout (UVLO): 5.5V (except Buck)
• Overvoltage Lockout (OVLO)
- 20V (MCP8025)
- 32V (MCP8026)
• Transient (100 ms) Voltage Tolerance: 48V
• Extended Temperature Range (TA): -40 to +150℃
• Thermal Shutdown
MCP8025应用:
• Automotive Fuel, Water, Ventilation Motors
• Home Appliances
• Permanent Magnet Synchronous Motor (PMSM)Control
• Hobby Aircraft, Boats, Vehicles
图1.MCP8025功能框图
图2. MCP8026功能框图
图3. MCP8025典型应用电路
图4. MCP8026典型应用电路
MCP8025 TQFP BLDC马达驱动评估板
The MCP8025 TQFP BLDC Motor Driver Evaluation Board is used to demonstrate thedrive capabilities of the MCP8025. The board uses the MCP8025 3-Phase BrushlessDC (BLDC) motor gate driver and dsPIC33EP256MC504 processor to implement a6-step trapezoidal BLDC motor controller.
The MCP8025 TQFP BLDC Motor Driver Evaluation Board is used to evaluateMicrochip’s MCP8025 in a BLDC motor application. As provided, the MCP8025 TQFPBLDC Motor Driver Evaluation Board is ready to operate a BLDC motor using oneon-board push button to start and stop the motor plus one on-board potentiometer toset motor speed. The evaluation board can drive a BLDC motor with a supply voltageof up to 19V and a motor current up to 15 amps. The MCP8025 TQFP BLDC MotorDriver Evaluation Board provides a 6-step trapezoidal control algorithm along with a750 mW buck converter, 5V and 12V LDO, high-to-low level voltage translators, currentsense operational amplifiers, LIN transceiver and Hall-effect inputs. The evaluationboard provides a status indication for the power supplies and the six on-boardPulse-Width Modulation (PWM) inputs.
MCP8025 TQFP BLDC马达驱动评估板主要特性:
• Input Operating Voltage Range: +6.0V to +19V
• Maximum of 500 mA of gate drive current for external N-Channel MOSFETs
• Drives up to a 15A BLDC motor
• 750 mW Buck Regulator with resistor-programmable output voltage
• ON/OFF momentary contact switch
• Reset momentary contact switch
• Spare user-programmable momentary contact switch
• PWM signal LED indicators
• PICkit 3 and MPLAB ICD 3 debugger interfaces
• Speed control potentiometer
• Terminal block for 5V and 12V Hall-effect sensors
• LIN terminal block for user communications use
• Programmable external MOSFET overcurrent protection
• Programmable PWM dead-time protection
• Programmable PWM blanking time for current switching spikes
• Complete “C” source code (provided on the board web page)
图5.MCP8025 TQFP BLDC马达驱动评估板框图
图6. MCP8025 TQFP BLDC马达驱动评估板外形图
图7. MCP8025 TQFP BLDC马达驱动评估板电路图
MCP8025 TQFP BLDC马达驱动评估板材料清单:
图8. MCP8025 TQFP BLDC马达驱动评估板PCB元件布局图
图9. MCP8025 TQFP BLDC马达驱动评估板PCB金属层设计图(顶层)
图10. MCP8025 TQFP BLDC马达驱动评估板PCB MID1金属层设计图
图11. MCP8025 TQFP BLDC马达驱动评估板PCB MID2金属层设计图
图12. MCP8025 TQFP BLDC马达驱动评估板PCB金属层设计图(底层)
The MCP8025/6 devices are 3-phase brushless DC(BLDC) power modules containing three integratedhalf-bridge drivers capable of driving three externalNMOS/NMOS transistor pairs. The three half-bridgedrivers are capable of delivering a peak output currentof 0.5A at 12V for driving high-side and low-side NMOSMOSFET transistors. The drivers have shoot-through,overcurrent and short-circuit protection. A Sleep Modehas been added to achieve a typical “key-off” quiescentcurrent of 5 μA.
The MCP8025 device integrates a comparator, a buckvoltage regulator, two LDO regulators, powermonitoring comparators, an overtemperature sensor, aLIN transceiver, a zero-crossing detector, a neutralsimulator and an operational amplifier for motor current monitoring. The phase comparator and multiplexerallow for hardware commutation detection. The neutralsimulator allows commutation detection without aneutral tap in the motor. The buck converter is capableof delivering 750 mW of power for powering acompanion microcontroller. The buck regulator may bedisabled if not used. The on-board 5V and 12V lowdropoutvoltage regulators are capable of delivering30 mA of current.
The MCP8026 replaces the LIN transceiver, neutralsimulator and zero-crossing detector in MCP8025 withtwo level shifters and two additional op amps.
The MCP8025/6 operation is specified over atemperature range of -40℃ to +150℃.Package options include 40-lead 5x5 QFN and 48-lead7x7 TQFP with Exposed Pad (EP).
MCP8025主要特性:
• AEC-Q100 Grade 0 Qualified
• Quiescent Current:
- Sleep Mode: 5 μA Typical
- Standby Mode:<200 μA
• LIN Transceiver Interface (MCP8025):
- Compliant with LIN Bus Specifications 1.3,2.2, and SAE J2602
- Supports baud rates up to 20K baud
- Internal pull-up resistor and diode
- Protected against ground shorts
- Protected against loss of ground
- Automatic thermal shutdown
- LIN Bus dominant timeout
• Three Half-Bridge Drivers Configured to DriveExternal High-Side NMOS and Low-Side NMOSMOSFETs:
- Independent input control for high-sideNMOS and low-side NMOS MOSFETs
- Peak output current: 0.5A @ 12V
- Shoot-through protection
- Overcurrent and short circuit protection
• Adjustable Output Buck Regulator (750 mW)
• Fixed Output Linear Regulators:
- email protected
- email protected
• Operational Amplifiers:
- one in MCP8025
- three in MCP8026
• Overcurrent Comparator with DAC Reference
• Phase Comparator With Multiplexer (MCP8025)
• Neutral Simulator (MCP8025)
• Level Translators (MCP8026)
• Input Voltage Range: 6V – 40V
• Operational Voltage Range:
- 6V–19V (MCP8025)
- 6V–28V (MCP8026)
• Buck Regulator Undervoltage Lockout: 4.0V
• Undervoltage Lockout (UVLO): 5.5V (except Buck)
• Overvoltage Lockout (OVLO)
- 20V (MCP8025)
- 32V (MCP8026)
• Transient (100 ms) Voltage Tolerance: 48V
• Extended Temperature Range (TA): -40 to +150℃
• Thermal Shutdown
MCP8025应用:
• Automotive Fuel, Water, Ventilation Motors
• Home Appliances
• Permanent Magnet Synchronous Motor (PMSM)Control
• Hobby Aircraft, Boats, Vehicles
图1.MCP8025功能框图
图2. MCP8026功能框图
图3. MCP8025典型应用电路
图4. MCP8026典型应用电路
MCP8025 TQFP BLDC马达驱动评估板
The MCP8025 TQFP BLDC Motor Driver Evaluation Board is used to demonstrate thedrive capabilities of the MCP8025. The board uses the MCP8025 3-Phase BrushlessDC (BLDC) motor gate driver and dsPIC33EP256MC504 processor to implement a6-step trapezoidal BLDC motor controller.
The MCP8025 TQFP BLDC Motor Driver Evaluation Board is used to evaluateMicrochip’s MCP8025 in a BLDC motor application. As provided, the MCP8025 TQFPBLDC Motor Driver Evaluation Board is ready to operate a BLDC motor using oneon-board push button to start and stop the motor plus one on-board potentiometer toset motor speed. The evaluation board can drive a BLDC motor with a supply voltageof up to 19V and a motor current up to 15 amps. The MCP8025 TQFP BLDC MotorDriver Evaluation Board provides a 6-step trapezoidal control algorithm along with a750 mW buck converter, 5V and 12V LDO, high-to-low level voltage translators, currentsense operational amplifiers, LIN transceiver and Hall-effect inputs. The evaluationboard provides a status indication for the power supplies and the six on-boardPulse-Width Modulation (PWM) inputs.
MCP8025 TQFP BLDC马达驱动评估板主要特性:
• Input Operating Voltage Range: +6.0V to +19V
• Maximum of 500 mA of gate drive current for external N-Channel MOSFETs
• Drives up to a 15A BLDC motor
• 750 mW Buck Regulator with resistor-programmable output voltage
• ON/OFF momentary contact switch
• Reset momentary contact switch
• Spare user-programmable momentary contact switch
• PWM signal LED indicators
• PICkit 3 and MPLAB ICD 3 debugger interfaces
• Speed control potentiometer
• Terminal block for 5V and 12V Hall-effect sensors
• LIN terminal block for user communications use
• Programmable external MOSFET overcurrent protection
• Programmable PWM dead-time protection
• Programmable PWM blanking time for current switching spikes
• Complete “C” source code (provided on the board web page)
图5.MCP8025 TQFP BLDC马达驱动评估板框图
图6. MCP8025 TQFP BLDC马达驱动评估板外形图
图7. MCP8025 TQFP BLDC马达驱动评估板电路图
MCP8025 TQFP BLDC马达驱动评估板材料清单:
图8. MCP8025 TQFP BLDC马达驱动评估板PCB元件布局图
图9. MCP8025 TQFP BLDC马达驱动评估板PCB金属层设计图(顶层)
图10. MCP8025 TQFP BLDC马达驱动评估板PCB MID1金属层设计图
图11. MCP8025 TQFP BLDC马达驱动评估板PCB MID2金属层设计图
图12. MCP8025 TQFP BLDC马达驱动评估板PCB金属层设计图(底层)
|
||||||
 |
||||||
|
||||||
