当前位置：首 页 --> 方案设计
MSP430FR4133低功耗FRAM存储器系列MCU开发方案
发布时间：2014/10/14 10:03:00 来源：
TI公司的MSP430FR4133是集成了低功耗FRAM存储器的MCU,具有不同的外设组合以适应各种应用.器件具有功能强大的16位RISC CPU,16位寄存器,最大代码效率的常数发生器.CPU工作频率高达16MHz,工作电压1.8V-3.6V,主要用于A/C遥控,衡器,水表,热表和气表,建筑物温度控制,血压计,血糖仪以及低功耗显示驱动器和一次性密码令牌.本文介绍了MSP430FR4133主要特性和功能框图, MSP430FR4133 LaunchPad开发板主要特性,框图,电路图和材料清单.
The Texas Instruments MSP430 family of low-power microcontrollers consists of several devices that feature different sets of peripherals targeted for various applications. The architecture, combined with extensive low-power modes, is optimized to achieve extended battery life in portable measurement applications. The device features a powerful 16-bit RISC CPU, 16-bit registers, and constant generators that contribute to maximum code efficiency. The digitally controlled oscillator (DCO) allows the device to wake up from low-power modes to active mode in less than 10 µs.
MSP430FR4133主要特性:
Embedded Microcontroller
16-Bit RISC Architecture up to 16 MHz
Wide Supply Voltage Range From 1.8 V to 3.6 V
Optimized Low-Power Modes (at 3 V)
Active Mode: 126 µA/MHz
Standby Mode: 770 nA With Real-Time Clock (RTC) Counter and Liquid Crystal Display (LCD)
Shutdown (LPM4.5): 15 nA
Low-Power Ferroelectric RAM (FRAM)
Up to 15.5KB of Nonvolatile Memory
Built-In Error Correction Code (ECC)
Configurable Write Protection
Unified Memory of Program, Constants, and Storage
1015 Write Cycle Endurance
Radiation Resistant and Nonmagnetic
Intelligent Digital Peripherals
IR Modulation Logic
Two 16-Bit Timers With Three Capture/Compare Registers Each (Timer_A3)
One 16-Bit Counter-Only Real-Time Clock counter (RTC)
16-Bit Cyclic Redundancy Checker (CRC)
Enhanced Serial Communications
Enhanced USCI A (eUSCI_A) Supports UART, IrDA, and SPI
Enhanced USCI B (eUSCI_B) Supports SPI and I2C
High-Performance Analog
10-Channel 10-Bit Analog-to-Digital Converter (ADC)
Internal 1.5-V Reference
Sample-and-Hold 200 ksps
Low-Power Liquid Crystal Display (LCD)
Supports up to 4x36- or 8x32-Segment LCD Configuration
On-Chip Charge Pump to Keep LCD Active in Standby Mode (LPM3.5)
Each LCD Pin Software Configurable as SEG or COM
Contrast Control From 2.6 V to 3.5 V by 0.06-V Steps
Clock System (CS)
On-Chip 32-kHz RC Oscillator (REFO)
On-Chip 16-MHz Digitally Controlled Oscillator (DCO) With Frequency Locked Loop (FLL)
±1% Accuracy With On-Chip Reference at Room Temperature
On-Chip Very Low-Frequency 10-kHz Oscillator (VLO)
On-Chip High-Frequency Modulation Oscillator (MODOSC)
External 32-kHz Crystal Oscillator (XT1)
Programmable MCLK Prescalar of 1 to 128
SMCLK Derived From MCLK With Programmable Prescalar of 1, 2, 4, or 8
General Input/Output and Pin Functionality
Total 60 I/Os on 64-Pin Package
16 Interrupt Pins (P1 and P2) Can Wake Up MCU From LPMs
All I/Os are Capacitive Touch I/O
Development Tools and Software
Free Professional Development Environments
Development Kit (MSP-TS430PM64D)
Family Members
MSP430FR4133: 15KB of Program FRAM + 512B of Information FRAM + 2KB of RAM
MSP430FR4132: 8KB of Program FRAM + 512B of Information FRAM + 1KB of RAM
MSP430FR4131: 4KB of Program FRAM + 512B of Information FRAM + 512B of RAM
Package Options
64-Pin: LQFP (PM)
56-Pin: TSSOP (G56)
48-Pin: TSSOP (G48)
MSP430FR4133应用:
A/C Remote Controller
Weigh Scale
Water Meter, Heat Meter, Gas Meter
In-Building Thermostat
Blood Pressure Meter
Low-Power Display Driver
One-Time-Password Token
Blood Glucose or Blood Pressure Meter
图1. MSP430FR4133功能框图
MSP430FR4133 LaunchPad开发板
The MSP-EXP430FR4133 LaunchPad development kit is an easy-to-use Evaluation Module (EVM) for the MSP430FR4133 microcontroller. It contains everything needed to start developing on the MSP430 Ultra-low-power (ULP) FRAM-based microcontroller (MCU) platform, including on-board emulation for programming, debugging and energy measurements. The board features on-board buttons and LEDs for quick integration of a simple user interface as well as a Liquid Crystal Display (LCD) display which showcases the integrated driver with flexible software-configurable pins. The MSP430FR4133 device features embedded FRAM (Ferroelectric Random Access Memory), a non-volatile memory known for its ultra-low power, high endurance and high speed write access.
Rapid prototyping is simplified by the 20-pin BoosterPack™ plug-in module headers, which support a wide range of available BoosterPacks. You can quickly add features like wireless connectivity, graphical displays, environmental sensing, and much more. Design your own BoosterPack or choose among many already available from TI and third party developers. The out-of-box provided with the MSP-EXP430FR4133 LaunchPad features the on-board segmented display and offers two operating modes. Stopwatch Mode can run a timer for up to 100 hours, or alternatively operate split time, where the display can be frozen and the stopwatch continues running in the background. The second mode provides a simple thermometer application using the on-chip temperature sensor. The temperature is displayed on the LCD and can be shown in degrees Fahrenheit or Celsius. Free software development tools are also available, such as TI’s Eclipse-based Code Composer Studio and IAR Embedded Workbench. Both of these IDEs support EnergyTrace technology when paired with the MSP430FR4133 LaunchPad. More information about the LaunchPad, the supported BoosterPacks and available resources can be found at TI’s LaunchPad portal.
MSP430FR4133 LaunchPad开发板主要特性:
MSP430 ULP FRAM-based MSP430FR4133 16-bit MCU 16KB FRAM
16-Bit RISC Architecture up to 8-MHz FRAM access/ 16MHz system clock speed
3 x Timer Blocks
10Ch 10-Bit ADC
8 x 32 segment LCD driver with integrated charge pump and configurable pins
EnergyTrace available for ultra-low-power debugging
20 pin LaunchPad standard leveraging the BoosterPack ecosystem
Onboard eZ-FET emulation
2 buttons and 2 LEDs for User Interaction
Segmented LCD
图2. MSP430FR4133 LaunchPad开发板外形图
图3. MSP430FR4133 LaunchPad开发板外框图
MSP430FR4133 LaunchPad开发套件包括:
1x MSP-EXP430FR4133 LaunchPad Development Kit
1x Micro USB cable
1x Quick Start Guide
图4. MSP430FR4133 LaunchPad开发板电路图(1)
图5. MSP430FR4133 LaunchPad开发板电路图(2)
图6. MSP430FR4133 LaunchPad开发板电路图(3)
图7. MSP430FR4133 LaunchPad开发板电路图(4)
图8. MSP430FR4133 LaunchPad开发板电路图(5)
图9. MSP430FR4133 LaunchPad开发板电路图(6)
The Texas Instruments MSP430 family of low-power microcontrollers consists of several devices that feature different sets of peripherals targeted for various applications. The architecture, combined with extensive low-power modes, is optimized to achieve extended battery life in portable measurement applications. The device features a powerful 16-bit RISC CPU, 16-bit registers, and constant generators that contribute to maximum code efficiency. The digitally controlled oscillator (DCO) allows the device to wake up from low-power modes to active mode in less than 10 µs.
MSP430FR4133主要特性:
Embedded Microcontroller
16-Bit RISC Architecture up to 16 MHz
Wide Supply Voltage Range From 1.8 V to 3.6 V
Optimized Low-Power Modes (at 3 V)
Active Mode: 126 µA/MHz
Standby Mode: 770 nA With Real-Time Clock (RTC) Counter and Liquid Crystal Display (LCD)
Shutdown (LPM4.5): 15 nA
Low-Power Ferroelectric RAM (FRAM)
Up to 15.5KB of Nonvolatile Memory
Built-In Error Correction Code (ECC)
Configurable Write Protection
Unified Memory of Program, Constants, and Storage
1015 Write Cycle Endurance
Radiation Resistant and Nonmagnetic
Intelligent Digital Peripherals
IR Modulation Logic
Two 16-Bit Timers With Three Capture/Compare Registers Each (Timer_A3)
One 16-Bit Counter-Only Real-Time Clock counter (RTC)
16-Bit Cyclic Redundancy Checker (CRC)
Enhanced Serial Communications
Enhanced USCI A (eUSCI_A) Supports UART, IrDA, and SPI
Enhanced USCI B (eUSCI_B) Supports SPI and I2C
High-Performance Analog
10-Channel 10-Bit Analog-to-Digital Converter (ADC)
Internal 1.5-V Reference
Sample-and-Hold 200 ksps
Low-Power Liquid Crystal Display (LCD)
Supports up to 4x36- or 8x32-Segment LCD Configuration
On-Chip Charge Pump to Keep LCD Active in Standby Mode (LPM3.5)
Each LCD Pin Software Configurable as SEG or COM
Contrast Control From 2.6 V to 3.5 V by 0.06-V Steps
Clock System (CS)
On-Chip 32-kHz RC Oscillator (REFO)
On-Chip 16-MHz Digitally Controlled Oscillator (DCO) With Frequency Locked Loop (FLL)
±1% Accuracy With On-Chip Reference at Room Temperature
On-Chip Very Low-Frequency 10-kHz Oscillator (VLO)
On-Chip High-Frequency Modulation Oscillator (MODOSC)
External 32-kHz Crystal Oscillator (XT1)
Programmable MCLK Prescalar of 1 to 128
SMCLK Derived From MCLK With Programmable Prescalar of 1, 2, 4, or 8
General Input/Output and Pin Functionality
Total 60 I/Os on 64-Pin Package
16 Interrupt Pins (P1 and P2) Can Wake Up MCU From LPMs
All I/Os are Capacitive Touch I/O
Development Tools and Software
Free Professional Development Environments
Development Kit (MSP-TS430PM64D)
Family Members
MSP430FR4133: 15KB of Program FRAM + 512B of Information FRAM + 2KB of RAM
MSP430FR4132: 8KB of Program FRAM + 512B of Information FRAM + 1KB of RAM
MSP430FR4131: 4KB of Program FRAM + 512B of Information FRAM + 512B of RAM
Package Options
64-Pin: LQFP (PM)
56-Pin: TSSOP (G56)
48-Pin: TSSOP (G48)
MSP430FR4133应用:
A/C Remote Controller
Weigh Scale
Water Meter, Heat Meter, Gas Meter
In-Building Thermostat
Blood Pressure Meter
Low-Power Display Driver
One-Time-Password Token
Blood Glucose or Blood Pressure Meter
图1. MSP430FR4133功能框图
MSP430FR4133 LaunchPad开发板
The MSP-EXP430FR4133 LaunchPad development kit is an easy-to-use Evaluation Module (EVM) for the MSP430FR4133 microcontroller. It contains everything needed to start developing on the MSP430 Ultra-low-power (ULP) FRAM-based microcontroller (MCU) platform, including on-board emulation for programming, debugging and energy measurements. The board features on-board buttons and LEDs for quick integration of a simple user interface as well as a Liquid Crystal Display (LCD) display which showcases the integrated driver with flexible software-configurable pins. The MSP430FR4133 device features embedded FRAM (Ferroelectric Random Access Memory), a non-volatile memory known for its ultra-low power, high endurance and high speed write access.
Rapid prototyping is simplified by the 20-pin BoosterPack™ plug-in module headers, which support a wide range of available BoosterPacks. You can quickly add features like wireless connectivity, graphical displays, environmental sensing, and much more. Design your own BoosterPack or choose among many already available from TI and third party developers. The out-of-box provided with the MSP-EXP430FR4133 LaunchPad features the on-board segmented display and offers two operating modes. Stopwatch Mode can run a timer for up to 100 hours, or alternatively operate split time, where the display can be frozen and the stopwatch continues running in the background. The second mode provides a simple thermometer application using the on-chip temperature sensor. The temperature is displayed on the LCD and can be shown in degrees Fahrenheit or Celsius. Free software development tools are also available, such as TI’s Eclipse-based Code Composer Studio and IAR Embedded Workbench. Both of these IDEs support EnergyTrace technology when paired with the MSP430FR4133 LaunchPad. More information about the LaunchPad, the supported BoosterPacks and available resources can be found at TI’s LaunchPad portal.
MSP430FR4133 LaunchPad开发板主要特性:
MSP430 ULP FRAM-based MSP430FR4133 16-bit MCU 16KB FRAM
16-Bit RISC Architecture up to 8-MHz FRAM access/ 16MHz system clock speed
3 x Timer Blocks
10Ch 10-Bit ADC
8 x 32 segment LCD driver with integrated charge pump and configurable pins
EnergyTrace available for ultra-low-power debugging
20 pin LaunchPad standard leveraging the BoosterPack ecosystem
Onboard eZ-FET emulation
2 buttons and 2 LEDs for User Interaction
Segmented LCD
图2. MSP430FR4133 LaunchPad开发板外形图
图3. MSP430FR4133 LaunchPad开发板外框图
MSP430FR4133 LaunchPad开发套件包括:
1x MSP-EXP430FR4133 LaunchPad Development Kit
1x Micro USB cable
1x Quick Start Guide
图4. MSP430FR4133 LaunchPad开发板电路图(1)
图5. MSP430FR4133 LaunchPad开发板电路图(2)
图6. MSP430FR4133 LaunchPad开发板电路图(3)
图7. MSP430FR4133 LaunchPad开发板电路图(4)
图8. MSP430FR4133 LaunchPad开发板电路图(5)
图9. MSP430FR4133 LaunchPad开发板电路图(6)
|
||||||
 |
||||||
|
||||||
