当前位置：首 页 --> 方案设计
L6472全集成微步进马达驱动方案
发布时间：2014/8/19 9:51:00 来源：
ST公司的L6472全集成微步进马达驱动器,采用模拟混合信号技术,集成了低RDS(on) DMOS全桥和所有的功率开关以及精确的片上电流检测电路,工作电压8-45V,输出峰值电流7.0A,高达1/16的微步进,非常适合驱动带微步进的两相双极步进马达.本文介绍了L6472主要特性,框图,应用电路以及采用L6472和STM32的评估板EVAL6472H-DISC主要特性,电路图,材料清单和PCB设计图与元件布局图.
The L6472 device, realized in analog mixed signal technology, is an advanced fully integrated solution suitable for driving two-phase bipolar stepper motors with microstepping. It integrates a dual low RDS(on) DMOS full bridge with all of the power switches equipped with an accurate on-chip current sensing circuitry suitable for non dissipative current control and overcurrent protection. Thanks to a new current control, a 1/16 microstepping is achieved through an adaptive decay mode which outperforms traditional implementations. The digital control core can generate user defined motion profiles with acceleration, deceleration, speed or target position, easily programmed through a dedicated register set.
All application commands and data registers, including those used to set analog values (i.e. current control value, current protection trip point, deadtime, etc.) are sent through a standard 5-Mbit/s SPI.
A very rich set of protections (thermal, low bus voltage, overcurrent) makes the L6472 device“bullet proof”, as required by the most demanding motor control applications.
L6472主要特性:
Operating voltage: 8 - 45 V
7.0 A output peak current (3.0 A r.m.s.)
Low RDS(on) Power MOSFETs
Programmable speed profile
Programmable Power MOSFET slew rate
Up to 1/16 microstepping
Predictive current control with adaptive decay
Non dissipative current sensing
SPI interface
Low quiescent and standby currents
Programmable non dissipative overcurrent protection on all Power MOSFETs
Two levels of overtemperature protection
L6472应用:
Bipolar stepper motor
图1. L6472框图
图2. L6472双极步进马达控制电路图
采用L6472和STM32的评估板EVAL6472H-DISC
The EVAL6472H-DISC can be used together with the STM32™ firmware library V1.0 and constitutes a complete motor control evaluation and a development platform.It is a demonstration board for motor control applications in the range of 8 V to 45 V of DC bus voltage using the STM32F105RB microcontroller with an internal 128 kB Flash size and a 64 kB internal RAM and the L6472H fully integrated solution suitable for driving two-phase bipolar stepper motors up to 1/16 microstepping.
The L6472H device integrates a dual DMOS full bridge with all of the power switches equipped with an accurate on-chip current sensing circuitry suitable for non-dissipative current control and overcurrent protection.
With dedicated hardware evaluation features, the EVAL6472H-DISC board is designed to help developers evaluate the device and develop their own applications.
评估板EVAL6472H-DISC主要特性:
DC voltage range from 8 V to 45 V
Maximum load phase current at 3 A r.m.s.
Footprint for external resonator or crystal
Control interface through trimmer - user keys and switch motor input
Control through LED indicators
Interface control by USB and debug outputs
Compatible with SPIN family evaluation tool
Autonomous board due to embedded firmware
Up to 1/16 microstepping
Optimized layout on 2-layer board - low cost and high thermal performance
评估板EVAL6472H-DISC目标应用:
The demonstration board is designed to fit all typical stepper motor applications - it is an
autonomous board due to embedded firmware.
图3. 评估板EVAL6472H-DISC外形图
图4. 评估板EVAL6472H-DISC电路图
图5. 评估板EVAL6472H-DISC PCB元件布局图:顶层
图6. 评估板EVAL6472H-DISC PCB设计图
评估板EVAL6472H-DISC 材料清单:
The L6472 device, realized in analog mixed signal technology, is an advanced fully integrated solution suitable for driving two-phase bipolar stepper motors with microstepping. It integrates a dual low RDS(on) DMOS full bridge with all of the power switches equipped with an accurate on-chip current sensing circuitry suitable for non dissipative current control and overcurrent protection. Thanks to a new current control, a 1/16 microstepping is achieved through an adaptive decay mode which outperforms traditional implementations. The digital control core can generate user defined motion profiles with acceleration, deceleration, speed or target position, easily programmed through a dedicated register set.
All application commands and data registers, including those used to set analog values (i.e. current control value, current protection trip point, deadtime, etc.) are sent through a standard 5-Mbit/s SPI.
A very rich set of protections (thermal, low bus voltage, overcurrent) makes the L6472 device“bullet proof”, as required by the most demanding motor control applications.
L6472主要特性:
Operating voltage: 8 - 45 V
7.0 A output peak current (3.0 A r.m.s.)
Low RDS(on) Power MOSFETs
Programmable speed profile
Programmable Power MOSFET slew rate
Up to 1/16 microstepping
Predictive current control with adaptive decay
Non dissipative current sensing
SPI interface
Low quiescent and standby currents
Programmable non dissipative overcurrent protection on all Power MOSFETs
Two levels of overtemperature protection
L6472应用:
Bipolar stepper motor
图1. L6472框图
图2. L6472双极步进马达控制电路图
采用L6472和STM32的评估板EVAL6472H-DISC
The EVAL6472H-DISC can be used together with the STM32™ firmware library V1.0 and constitutes a complete motor control evaluation and a development platform.It is a demonstration board for motor control applications in the range of 8 V to 45 V of DC bus voltage using the STM32F105RB microcontroller with an internal 128 kB Flash size and a 64 kB internal RAM and the L6472H fully integrated solution suitable for driving two-phase bipolar stepper motors up to 1/16 microstepping.
The L6472H device integrates a dual DMOS full bridge with all of the power switches equipped with an accurate on-chip current sensing circuitry suitable for non-dissipative current control and overcurrent protection.
With dedicated hardware evaluation features, the EVAL6472H-DISC board is designed to help developers evaluate the device and develop their own applications.
评估板EVAL6472H-DISC主要特性:
DC voltage range from 8 V to 45 V
Maximum load phase current at 3 A r.m.s.
Footprint for external resonator or crystal
Control interface through trimmer - user keys and switch motor input
Control through LED indicators
Interface control by USB and debug outputs
Compatible with SPIN family evaluation tool
Autonomous board due to embedded firmware
Up to 1/16 microstepping
Optimized layout on 2-layer board - low cost and high thermal performance
评估板EVAL6472H-DISC目标应用:
The demonstration board is designed to fit all typical stepper motor applications - it is an
autonomous board due to embedded firmware.
图3. 评估板EVAL6472H-DISC外形图
图4. 评估板EVAL6472H-DISC电路图
图5. 评估板EVAL6472H-DISC PCB元件布局图:顶层
图6. 评估板EVAL6472H-DISC PCB设计图
评估板EVAL6472H-DISC 材料清单:
|
||||||
 |
||||||
|
||||||
